Labview Error Codes 2011
Poor|Excellent Yes No Document Quality? YourFeedback! Set the Invoke Node class to VI and select the Run VI method. 1198 The VI is not in a state compatible with this operation. Refer to the KnowledgeBase for more information about correcting errors in LabVIEW. Check This Out
All cells must contain the same number of observations. −20046 There is an overflow in the calculation. −20045 The total number of data points must be equal to the result of This error also can occur if you try to run a VI using the run method while the target VI is running or reserved for running. Select Customize»View This Palette As from the Controls or Functions palette to change the palette view format. −4401 The specified file is not a valid palette file (.mnu). For example, if you are connecting to an endpoint with the name Endpoint1 on a computer with the IP address 10.0.0.62, use the URL //10.0.0.62/stream1. −314004 LabVIEW could not create the http://zone.ni.com/reference/en-XX/help/371361H-01/lverror/misc_lv_error_codes/
This is caused by trying to allocate a buffer that is too large for memory. Ensure that you specify the URL of a remote endpoint with the reader url terminal of the Create Network Stream Writer Endpoint function or the writer url terminal of the Create Check the ref units input. −20313 Reference levels do not satisfy requirements. There are not enough format specifiers to match all of the arguments of a Format Into String or Scan From String function. 84 Too many format specifiers.
If the problem persists, contact National Instruments technical support. −20323 The edge number, pulse number, or cycle parameter value must be greater than zero. −20322 Internal error: The attribute number does This error occurs when you try to use the Default Frame property with a Diagram Disable structure. event. Add Comments 1 2 3 4 5 My Profile|Privacy|Legal|Contact NI© National Instruments Corporation.
You can link a control reference only to controls or indicators in the same VI. 1583 LabVIEW Real-Time target is already connected to a host VI. The return type must be Void, Numeric, or String. TipActiveX error codes are documented by Microsoft in winerror.h. click to read more All rights reserved.| Cart|Help You are here:NI Home > Support > Manuals > LabVIEW 2011 Help Ranges of LabVIEW Error Codes »Table of Contents LabVIEW 2011 Help Edition Date:
For example, use \ as path separators on Windows, : on Mac OS X, and / on Linux. Another array appears. Check that the parameters entered are within the supported range for the hardware and drivers. 4804 Cannot write in file playback. Another possible cause for this error is there might be a bad network connection.
or @. 2 Memory is full. 4 End of file encountered. 5 File already open. 6 Generic file I/O error. http://zone.ni.com/reference/en-XX/help/371361H-01/lverror/lverror_intro/ To correct this error, install the latest version of DirectX from http://www.microsoft.com/downloads. 4810 Cannot recognize sound format. Do not invoke any other handlers on this session for this event. 1073676441 Operation completed successfully, and this session has nested shared locks. 1073676442 Operation completed successfully, and this session has Contact National Instruments technical support if you receive an error message that is not listed in this book.
A possible cause for this error is the disk or hard drive to which you are trying to save might be full. http://distributedsimulation.com/labview-error/labview-error-codes-user.html The data types of the endpoints must match. −314240 The stream detected an unrecoverable loss of data. Enter a path to a valid palette file to write data to the file. −4400 The palette type is invalid. Check the signal length, reference levels, and ref level units. −20307 Frequency not a multiple of (Sampling Rate)/Samples. −20306 The two time signal waveforms contain different dt. −20305 The two time
VIs in libraries are saved in the form LIBRARYNAME_VINAME. You often can solve the problem by taking the following actions. Answered Your Question? http://distributedsimulation.com/labview-error/labview-error-codes-list.html This error can occur when you write a frequency domain waveform to a file with Segment Headers set to One header only.
This file cannot be saved until all dependent files have been named. 1022 Wizard Template not found. 1023 Wizard template does not have a diagram. 1024 Call Instrument aborted. 1025 Application Set Segment Headers to One header per segment to correct this error. 1 An input parameter is invalid. Each endpoint can connect to only one other endpoint at a time. −314106 The local endpoint is not connected to a remote endpoint.
This error also can occur if you attempt to obtain a VI's image while the VI is being modified programmatically.
Double-click the numeric constant and enter the same number that appears in the [user-defined codes] constant. Change the name of this endpoint so that it does not overlap with an existing name, or destroy the other endpoint before creating this endpoint. −314108 The name of one endpoint Make sure you entered the IP address or computer name of the server correctly. 1346 Server does not support remote panels. 1347 You cannot connect to the local LabVIEW application. 1348 A memory or network problem occurred.
Save the new VI or function to a different directory than vi.lib so you do not overwrite the original. 44 Object ID too low. 45 Object ID too high. 46 Object To correct this error, you must obtain a valid license for the VI and its containing library. 1390 You attempted to open a VI Server reference to an out-of-scope VI. Attempted to read from or write to a file of a type incompatible with the operation. navigate here Contact National Instruments for support. −314235 The remote endpoint was restarted because the computer that hosts the endpoint crashed, was rebooted, or experienced a hang. −314230 LabVIEW could not create the
Code resource already loaded. 1307 Subpanel control could not open the VI window. General Error Handler Simple Error Handler You also can select Help»Explain Error to display an error code description in the Explain Error dialog box. Error handler VIs also can display a dialog box with an error code description and buttons that can stop or continue execution. Answered Your Question?
To correct this error, check that the desired service name is correct. You must use an absolute path. 1432 The specified format cannot be used with floating point data.
© Copyright 2017 distributedsimulation.com. All rights reserved.