Labview Error 6
Try creating a new folder if you need to write more files. I think you should reconsider this. This error is caused by a problem with LabVIEW’s interaction with the file system.To resolve the problem: If you have created a large number of files, the folder on disk may After clicking on continue, the whole program continues properly but, of course, the values were not saved in the file. Check This Out
Nor did he provide any information about his application other than that it caused a specific error number. All rights reserved. | Cart|Help KnowledgeBase Request Supportfrom an engineer NIHome > Support > KnowledgeBase English 2 ratings: 2.5 out of 5   Why do In this case it is not even software I wrote so how would we have been able to even guess from the first two posts of the OP that GPIB might So, writing partial blocks to disk results in unwanted disk access as well as decrease in performance.
Labview Generic File I O Error Could Not Be Loaded
Most likely it is a file permission error. Share this post Link to post Share on other sites rolfk 369 LabVIEW Aficionado Members 369 2,613 posts Location:Netherlands Version:LabVIEW 2011 Since:1992 Posted July 9, 2015 Well, I will tell Solution: There are multiple reasons why you might be getting this error. When deleting a directory, either first delete its contents and subfolders, or wire a True constant to the entire hierarchy input of the Delete function.
My Profile | RSS | Privacy | Legal | Contact NI © 2014 National Instruments Corporation. It appears that I am inputting a valid file path, but I continuously get this error. Hi, If you want to stream data to disk as fast as possible, you must know the block size of the harddrive, and write data in chunks with size that is Labview Error Codes If you determine that control characters have been included, they can be replaced with a non-control character (such as underscore) by using the Search and Replace Pattern.vi located on the string
If using LabVIEW 6.1 or earlier, the file name must conform to the 8.3 naming convention. Remove or replace any control characters from string controls or constants that are used to construct a file path. Why does this occur? http://digital.ni.com/public.nsf/allkb/3CC2144F391E7C9C8625764D00722173 Primary Software: Primary Software Version: 7.1 Primary Software Fixed Version: N/A Secondary Software: LabVIEW Development Systems>>LabVIEW Base Package Problem: I am trying to use the Copy.vi from the File I/O subpalette
The path has been incorrectly specified, which is most often caused by improper formatting of the path. The disk where you are storing files becomes full. I see all the time old timers posting screenshots. Error 6 occurred at Keith 236 Read Meas; GPIB Send Message Possible reason(s): LabVIEW: Generic file I/O error. ========================= NI-488: I/O operation aborted.
Labview Generic File I/o Error. ========================= Ni-488 I/o Operation Aborted
Since this code is run continuously how big do these files get? 0 Kudos Message 4 of 5 (782 Views) Reply 0 Kudos Re: Error 6 in "Write To Spreadsheet File.vi" All rights reserved. Labview Generic File I O Error Could Not Be Loaded thanks again, your answer helped me Cheers Antoine Share this post Link to post Share on other sites Create an account or sign in to comment You need to be a Labview Error 6 Occurred At Delete But if I set (true) input "disable buffering" in Create/Open/Replace File vi, I get error 6...
Also check the available space on the disk drive. http://distributedsimulation.com/labview-error/labview-error-10.html The file is just a few dozens to a few hundred KB. However in this case, Copy.vi was being used to duplicate a file or directory to another computer using 2 network cards and a crossover ethernet cable. If I reset it (false ) I have no problem...if I set it under my host computer, not on the target, that works....Does it mean I can't disable buffering I/O transfert Generic File I/o Error Labview
The reason is that RT does not use buffering (probably the cause of error 6), and it must therefore read the old block before writing a partial block to disk. Is it running from a mapped drive? The preferred method of specifying file paths is to use a file path constant of c:\ and then use the Build Path VI to add your constant to the path. http://distributedsimulation.com/labview-error/labview-error.html Our ion gauge displays the pressure that is connected to the computer through GPIB connection. My Professor created a code that was made to read the pressure that is displayed
Answered Your Question? 1 2 3 4 5 Document needs work? All rights reserved. | Cart|Help KnowledgeBase Request Supportfrom an engineer NIHome > Support > KnowledgeBase English 8 ratings: 4.12 out of 5   Why Do My Profile | RSS | Privacy | Legal | Contact NI © 2014 National Instruments Corporation.
I handle a big amount of data coming from RT FIFO shared Var.
Member 08-08-2011 05:12 PM Options Mark as New Bookmark Subscribe Subscribe to RSS Feed Highlight Print Email to a Friend Report to a Moderator Hi amitin, What version of the The Windows file naming conventions are not met. This occurs when I use the various File I/O sub VI's that require file path as an input. Computer2\C:\SharedFolder), Error 6 will occur as shown above.
Please Contact NI for all product and support inquiries. You have not provided a command (the string) in the image you posted above. suppression_mod.vi 92 KB 0 Kudos Message 6 of 14 (2,391 Views) Reply 0 Kudos Re: error 6 jajassa Member 05-23-2006 03:01 AM Options Mark as New Bookmark Subscribe Subscribe to RSS navigate here But i do not care as long as you provide me with information. They are asking you to post the source (the actual VIs) not a text file or an
Ok, so disable buffering on RT target is not a way to follow. In this case it is not even software I wrote so how would we have been able to even guess from the first two posts of the OP that GPIB might Share this post Link to post Share on other sites chris754 8 Very Active Members 8 63 posts Version:LabVIEW 2013 Since:2006 Posted July 14, 2015 Sorry, For the late response Ensure that any file paths or directories being accessed by LabVIEW do not exceed the maximum length for system file paths.
Related Links: KnowledgeBase3BOD21PS: Why do I get "Error 1 occurred at Open VI Reference"?KnowledgeBase3DNI22CC: Why Do I get Error 6: Generic File I/O Error When Using the Copy VI? Please Contact NI for all product and support inquiries. Poor|Excellent Yes No Document Quality? See KB 3DN7C7CC in the related links for more information.
I would say path of the file, excuz me. Posting in OpenG made me actually guess at first it may be related to some OpenG toolkit function, otherwise I had left the post entirely alone in the first place. All rights reserved. | Jump to content Real-Time Existing user? If I set a non-existing directory (and even a non-existing drive) I get error 7 instead.As I wrote earlier I get the error for D: because it exists but the operating
© Copyright 2017 distributedsimulation.com. All rights reserved.